How to Build a Pergola Roof | Ep. 174

Kennith Bogan

Pergola with no roof over patio.
You can use your outdoor room even when it is raining by including a roof to a pergola.

A pergola roof safeguards you from pop-up storms, so you can increase your time outdoor.

Tyler Schwall in Mobile, Ala., desires to set up a tin roof above his pergola. But in advance of he does this, he needs to know the greatest way to set the roof so it has a pitch for rainwater.

To start with, get some stress-addressed 2-by-4s to cover each slat on the pergola. Make confident these boards are the exact length as the kinds on the pergola.

Then, rip each individual 2-by-4 at a slight angle from its total width down to almost nothing. Ripping a board implies reducing it together its length. This will create a tapered strip. Make sure the pitch of the roof is at the very least two inches so the rain will properly movement off of it.

Subsequent, use some building adhesive on the slats and position the ripped boards on top of them. This will insert some extra waterproofing protection and preserve them safe when you’re setting up the tin roof.

Right after you have positioned the ripped boards on the pergola, protected them with wooden screws. To preserve the tin roof from sagging, lay some 2-by-4s perpendicular to these. 

When all the boards are secure, put in the tin roof. 

Now, you can sit exterior under your covered pergola and enjoy the sound of the rain dancing on the tin roof. 

Skip to [21:58] for the comprehensive section on the Today’s Home owner Podcast.

Also in this episode:


Very best New Merchandise

 Two dogs run on Lifeproof with Petproof Technology Premium Pet Turf Whether or not you want to secure your garden from animals digging or produce a place for them to roam, Lifeproof Quality Pet Turf has you lined. Master more>> 

Uncomplicated Solutions

Finger twisting a bolt into the bottom of a wooden leg on patio furniture
This Very simple Resolution levels patio household furniture and assists reduce wood rot.

Leveling Wood Patio Home furnishings — Begin by tedious a 3/8-inch diameter gap into the bottom of every table or bench leg.

Then, use a hammer to tap a T-nut into just about every hole.

Thread a hex-head equipment bolt into just about every T-nut.

The bolts raise the bench off the patio to stop rot, and they are adjustable to make certain the bench is degree. 

Observe: Suggestion for Leveling Wooden Patio Furnishings  


A hacksaw cutting a bolt in a drill
If you have to have to minimize a bolt to dimension, enable a cordless drill do most of the work for you.

Clean-Cut Bolts — Here’s how to shorten a device bolt — threaded rod or carriage bolt — devoid of messing up the threads.

Initially, thread two hex nuts onto the bolt, then make the minimize employing a hacksaw or jigsaw with a metallic-slicing blade.

Then, spin off the nuts, a single at a time, utilizing a wrench if necessary.

When the nuts arrive off the finish of the bolt, they’ll re-slash and straighten out any threads that ended up ruined by the noticed, building it uncomplicated to thread the nut back on.  

Enjoy: Suggestion for Reducing Bolts to Size 


Engineered wood flooring with tools needed for installing.
Engineered wood flooring dramatically improvements the glimpse of the area, but you should have the right plank measurement right before you commence. (digidreamgrafix, Getty Photographs)

Concern of the Week

Q: I just bought my first household and I’m about to set up some engineered wood flooring.

In accordance to the installation recommendations, the past row of flooring have to not be considerably less than fifty percent the width of the planks. (The planks are 5 inches extensive.) But the guidelines really don’t convey to you how to figure out the width of the very last row.

Can you make sure you convey to me how to determine that out? 

A: When putting in flooring, the first structure is heading to define the success of the task. Do not commence with a comprehensive-width plank and hope the last row is huge enough. 

Initial, measure the width of the space and divide by 5, the width of the plank. That will give you the selection of comprehensive-width planks plus any fractions.

If the very last row is significantly less than 2½  inches, cut down the width of the initially plank. 

Skip to [36:22] for the complete segment on the Today’s House owner Podcast.



Additional Examining


Talk to a Question! (Podcast)

Question a problem and we could solution it on the “Present-day Home owner Podcast!” We also may use it on our nationally syndicated radio broadcast or on todayshomeowner.com.

Next Post

Prepare your home for the summer heat with over 20% off this air conditioner

We could receive commission from buys manufactured through hyperlinks on this web site. Pricing and availability are matter to modify. This articles is designed by a 3rd bash lover for Yahoo. Keep great this summer months with this 20% air conditioner. (Supply: Amazon) Summer season is here, and that signifies […]

You May Like